Waste water - Products

MOPA3500

Submersible electro-pump for drainage

APPLICATIONS

Submersible electro-pump suitable for water collection up to 2 mm. minimum level thanks to the impeller design.

Suitable for floodings in basements, garages and lifts, rain water collection and emptying of swimming-pools.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (l/h): 500 - 7000

Head (m): 0 - 7

rpm: 2900

IP: X8

Isolation: B

Cooling: Pumped water

Temp. max. (ºC): 35

Max. Immersion depth: 7 m.

Impeller: Open

Provided with 10 meters cable and hose outlet fitting.

Built-in thermo-amperimetric protection.

Includes new electronic vertical level switch with possibility to select different levels (3) for the automatic pump start.

The pump stops 1 minute after the water level is lower than the selected position in the level switch.

MATERIALS

Pump body: Polypropylene

Suction foot: Stainless steel

Impeller: Noryl

Shaft: ‘AISI 420’ Stainless steel

Mechanical seal: Ceramic/Graphite

The level switch has a position to make the pump to work in manual mode (without automatic stop).

DUPLEX100

Double-purpose submersible electro-pump for drainage

APPLICATIONS

Submersible electro-pump with extensible support foot and electronic vertical level switch recommended for drainage applications with little space.

It can be used with the support foot gathered up for clean water drainage.

Spread out for bailing waste water with suspended small foreign bodies.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (l/h): 13500 - 3000

Head (m): 1 - 8

rpm: 2900

IP: X8

Isolation: B

Cooling: Pumped water

Temp. max. (ºC): 35

Max. Immersion depth: 7 m.

Impeller: Displaced

Ø Solids: 5 mm

Provided with 10 meters cable and hose outlet fitting.

Built-in thermo-amperimetric protection.

Includes new electronic vertical level switch with possibility to select different levels (4) for the automatic pump start.

The pump stops 1 minute after the water level is lower than the selected position in the level switch.

MATERIALS

Pump body: Polypropylene

Base: Polypropylene

Impeller: Noryl

Diffuser: Polypropylene

Shaft.: ‘AISI 420’ Stainless steel

Mechanical seal: Ceramic/Graphite

SUBCC24V

Electro-pump direct voltage 24 v

APPLICATIONS

Submersible electro-pump suitable for bailing fresh or sea water.

TECHNICAL CHARACTERISTICS

Type: Submersible CC

Flow (l/h): 1000 - 9000

Head (m): 1 - 6

rpm: 4000

IP: 68

Isolation: B

Cooling: Pumped water

Temp. max. (ºC): 35

Impeller: Open

Provided with 10 meters of cable and hose outlet fitting.

Max. immersion depth: 5 m.

MATERIALS

Pump body: Polypropylene

Suction body: Polypropylene

Impeller: Noryl

Diffusers: Polypropylene

Shaft: Stainless steel

Mechanical seal: Ceramic/Graphite

TURBO

Submersible electro-pump for sump and loaded water

APPLICATIONS

Turbo 55: Submersible electro-pump suitable for rain water bailing, drainage inlets and ponds

TURBO 100 D: Submersible electro-pump suitable for sewage water with small suspended foreign bodies or particles.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (l/h): 500 - 13500

Head (m): 1 - 9

rpm: 2900

IP: X8

Isolation: B

Cooling: Pumped water

Temp. max. (ºC): 35

Max. Immersion depth: 7 m.

Provided with 10 meters of cable, level switch and hose outlet fitting.

Built-in thermo-amperimetric protection.

MATERIALS

Pump body: Stainless steel

Base: Stainless steel

Impeller: Noryl

Diffuser: Noryl

Shaft: ‘AISI 420’ Stainless steel

Mechanical seal: Ceramic/Graphite

DRINOX

Submersible electro-pump for drainage

APPLICATIONS

Submersible electro-pumps suitable for rain water drainage, dirty or filtered water, in garages, basements, swimming-pools, etc.

With high performance in drainage head thanks to its impeller and pump body design.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (l/h): 500 - 21000

Head (m): 0 - 18

rpm: 2850

IP: 68

Isolation: F

Cooling: Dielectric oil

Temp. max. (ºC): 40

Max. Immersion depth: 15 m.

Impeller: Open

Built-in thermo-amperimetric protection in all models.

All models are supplied with 5 meters of cable and level switch.

MATERIALS

Pump body: Noryl® with fiber glass

Suction grill: Noryl® with fiber glass

Pump housing: ‘AISI 304’ Stainless steel

Motor cover: ‘AISI 304’ Stainless steel

Handle: ‘AISI 304’ Stainless steel

Impeller: ‘AISI 304’ Stainless steel

Shaft: ‘AISI 316’ Stainless steel

Mechanical seal: Graphite/Alumina

INOXPALM

Submersible electro-pump for residual water

APPLICATIONS

Submersible electro-pumps.

Suitable for drainage of waste water, rain water, industrial water with suspended solid particles.

Vortex-type impeller with large distance for foreign bodies pitch.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (l/h): 1000 - 72000

Head (m): 0 - 19

rpm: 2850

IP: 68

Isolation: F

Cooling: Dielectric oil

Temp. max.(ºC): 40

Max. immersion depth: 15 m.

Impeller: Vortex

Built-in thermo-amperimetric protection in single-phase models.

Models Inox-Palm 1 and 2 are provided with 5 meters of cable and models Inox-Palm 2.5, 3, 4 and 5 with 10 meters of cable.

All single-phase models are provided with level switch.

Vertical level switch upon request

MATERIALS

Pump body: G20 Cast iron

Base: G20 Cast iron

Pump housing: ‘AISI 304’ Stainless steel

Motor cover: ‘AISI 304’ Stainless steel

Handle: ‘AISI 304’ Stainless steel

Impeller: INOX-PALM 1/2/2.5/3/4: ‘AISI 304’ Stainless steel, INOX-PALM 5: G20 Cast iron

Shaft: ‘AISI 420’ Stainless steel

Mechanical seal: INOX-PALM 1/2/2.5/3/4: Graphite/Alumina, INOX-PALM 5: Graphite/Alumina + Silicon-Carbide/Alumina

O'rings: NBR

IPX

Submersible electro-pump for sump and loaded water

APPLICATIONS

Submersible electro-pumps.

Submersible electro-pumps suitable for the drainage of waste water, rain water, industrial water with suspended solid particles.

Thanks to its vortex-type impeller with large distance pitch for particles

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (l/h): 1000 - 48000

Head (m): 0 - 21

rpm: 2850

IP: 68

Isolation: F

Cooling: Dielectric oil

Temp. max.(ºC): 40

Max. inmersion depth: 15 m.

Impeller: Vortex

Built-in thermo-amperimetric protection in all models.

Single-phase models are provided with level switch.

Models IPX 1A and 2A are provided with 5 meters of cable.

Models IPX 3 and 4 are provided with 10 meter of cable.

Vertical level switch upon request.

MATERIALS

Pump body: ‘AISI 304’ Stainless steel

Base: ‘AISI 304’ Stainless steel

Pump housing: ‘AISI 304’ Stainless steel

Motor cover: ‘AISI 304’ Stainless steel

Handle: ‘AISI 304’ Stainless steel

Impeller: ‘AISI 304’ Stainless steel

Shaft: ‘AISI 316’ Stainless steel

Mechanical seal: Graphite/Alumina

O'rings: NBR

MINIPAF

Submersible electro-pump for residual water

APPLICATIONS

Submersible electro-pump suitable for bailing waste water, sewage, septic tanks and water purification plants.

Pumps with open impeller allow liquid flow with suspended solid particles.

Pumps with vortex impeller with total pitch, allow the flow of large solid particles almost of the same diameter as outlet.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (m3/h): 30 - 0,6

Head (m): 1 - 11

rpm: 2850

IP: 68

Isolation: F

Cooling: Oil and pumped water

Temp. max.(ºC): 40

Max. Immersion depth: 20 m.

pH: 6 - 11

Max. density: 1100 Kg/m3

Provided with 10 meters of cable, except 0,5 HP models (5 meters)

Single-phase models are provided with level switch.

MATERIALS

Pump body: G20 Cast iron

Motor cover: G20 Cast iron

Impeller: G20 Cast iron

Shaft: ‘AISI 420’ Stainless steel

Mechanical seal: Alumina/Silicon-Carbide

Screws: ‘AISI 304’ Stainless steel

Handle: Stainless steel

O’rings: NBR

PAF

Submersible electro-pump for residual water

APPLICATIONS

Submersible electro-pump suitable for pumping, waste water, septic tanks and water treatment plants.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (m3/h): 54 - 1,5

Head (m): 1 - 19

rpm: 2850

IP: 68

Isolation: F

Cooling: Oil and pumped water

Temp. max.(ºC): 40

Max. Immersion depth: 20 m.

pH: 6 - 11

Max. density: 1100 Kg/m3

Provided with 10 meters of cable.

Single-phase models are provided with level switch and start terminal box with capacitor.

MATERIALS

Pump body: G20 Cast iron

Motor cover: G20 Cast iron

Impeller: G20 Cast iron

Shaft: ‘AISI 416’ Stainless steel

Mechanical seal: - Lower side (pump): Silicon Carbide. - Upper side (motor): Alumina/Graphite.

Screws: Stainless steel

O’rings: NBR

Handle: Stainless steel

PAF20

Submersible electro-pump for residual water

APPLICATIONS

Submersible electropumps especially indicated for pumping of waste water, sewage, septic tanks and water treatment plants

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (m3/h): 135 - 3

Head (m): 4 - 31

rpm: 2850

IP: 68

Isolation: F

Cooling: Oil and pumped water

Temp. max.(ºC): 40

Max. Immersion depth: 20 m.

Impeller: Single-channel

Ø Solids: 50 mm

All models are supplied with 10 m of electric cable and counter-flange for assembly with o’ring and screws.

Supplied with support base for mobile installation or optionally with coupling foot for fixed installation.

None of the models includes level switch.

All the single-phase models include terminal box with capacitor.

MATERIALS

Pump body: Cast iron

Motor cover: Cast iron

Impeller: Cast iron

Shaft: ‘AISI 304’ Stainless steel

Mechanical seal: Lowe side (pump): Silicon carbide, Upper side (motor): Ceramic/Graphite

Screws: A2 Stainless steel

O’rings: NBR

AT

Submersible electro-pump for residual water

APPLICATIONS

Submersible electropumps of robust construction, suitable for different fluids such as: clean water, rain water, mixed water, waste water with suspended solids and fibrous content, muddy water, etc.

TECHNICAL CHARACTERISTICS

Type: Submersible

IP: 68

Isolation: F

Cooling: Oil and pumped water

Temp. max.(ºC): 40

Max. Immersion depth: 20 m.

pH: 6 - 10

Max. starts: 15/h

Max. sound level: 70 dB (A)

All models are supplied with 10 m of electric cable and counterflange for assembly with o’ring and screws.

The counter flange kit with gasket and screws, the support base for mobile installation and the coupling foot for fixed installation are not included with the pump and are supplied separately.

All pumps are equipped with 2 thermal sensors (T1/T2) in the winding which display the temperature inside the motor, and an electrode (S) wich produces a signal revealing a fluid infiltration in the mechanical seal chamber. These sensors should be correctly connected to the suitable control panel, which is not included with the pump.

The represented hydraulic characteristics are valid for fluids with density <1,1 kg/dm3.

Rotation direction: Clockwise from the upper side.

MATERIALS

Pump body: G25 Cast iron

Motor casing: G25 Cast iron

Motor cover: G25 Cast iron

Impeller: G25 Cast iron

Shaft: ‘AISI 420’ Stainless steel

Mechanical seal: - Lower side (pump): Silicon Carbide/Viton. - Upper side (motor): Ceramic/Graphite.

Screws: ‘AISI 304’ Stainless steel

O’rings: Viton

TYPE OF INSTALLATIONS

Mobile installation:

Pump mounted on support base for mobile operations in emergency cases.

The pump must work completely or partially plunged in the intervals 1 and 2 defined in the technical characteristics.

Installation fixe

The plunged stationary installations with two guide rails allow the automatic coupling of the pump at the foot of channeling and evacuation of the fluid.

The sealing of the installation is guaranteed by the pump’s own weight.

The pump can be easily extracted for works of maintenance without needing to enter in the working area.

The pumps must work completely or partially plunged in the intervals 1 and 2 defined in the technical characteristics.

LFC

Surface and semi-submersible electric pumps for wastewater

APPLICATIONS

Electro-pumps suitable for pumping dirty and waste water with solid particles.

Likewise, thanks to their making and design, they are irreplaceable in the food industry (macerated substances, fruit pulp, slaughterhouse waste, etc.), agricultural and livestock industry (manure, purines, etc.), paper and cellulose industry (particles of cellulose paper, pulp, pasted-water, etc.), chemical industry (waste water with chemical products, brine, alkaline water, etc.), construction industry (drainage, tank emptying, etc.)

TECHNICAL CHARACTERISTICS

Type: Waste water

Flow (m3/h): 2 - 180

Head (m): 2 - 30

Stardard: ICE

IP: 55

Isolation: F

r.p.m.: 1450 - 2850

Cooling: External ventilation

Rotation direction: Clockwise

MATERIALS

Pump body: Cast iron

Impeller: Cast iron (F) / Bronze (L)

Shaft: ‘AISI 420’ Stainless steel

Screws: Stainless steel

TYPE OF IMPELLERS

OPEN IMPELLER L series:

For dirty liquids or loaded with suspended solid particles.

The liquid to be pumped should not have elements such as long fibers or similar which may result in braids.

VORTEX IMPELLER F series:

For loaded liquids with high quantity of gas or air containing suspended solid particles and mixtures resulting in braids.

Free pitch for solids with Ø equivalent to the pump’s discharge and suction outlets.

TRITURANT130

Submersible electro-pump for residual water

APPLICATIONS

Submersible electro-pumps with grinding system suitable for the disposal of domestic waste water.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (m3/h): 3 - 22,8

Head (m): 2 - 14

rpm: 2850

IP: 68

Isolation: F

Cooling: Mineral oil and pumped water

Temp. max. (ºC): 40

Impeller: Grinder

Provided with 10 meters of cable.

Single-phase models are provided with level switch, thermal protection, capacitor, circuit breaker and ON-OFF switch.

MATERIALS

Pump body: G25 Cast iron

Motor casing: ‘AISI 304’ Stainless steel

Motor cover: G25 Cast iron

Impeller: G25 Cast iron

Grinder: Hardened ‘AISI 440’ stainless steel

Shaft: ‘AISI 420’ Stainless steel

Mechanical seal: Silicon Carbide

Screws: ‘AISI 304’ Stainless steel

TRITURANT

Submersible electro-pump for residual water

APPLICATIONS

Submersible electro-pumps suitable for low flowrates at high manometric head.

Thanks to its grinding system, they are suitable for waste water drainage in the civil, industrial, sanitary and agricultural sectors.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (m3/h): 0 - 21,6

Head (m): 9,9 - 54,6

IP: 68

Isolation: F

rpm: 2900

Cooling: Dielectric oil

Temp. max. (ºC): 40

Max. inmersión depth: 20 m.

All models are supplied with 10 m. of electric cable, counter-flange for assembly with joint and screws and support base.

All the single-phase models include terminal box with capacitor and circuit breaker.

None of the models includes level switch.

MATERIALS

Pump body: Cast iron

Impeller: Cast iron

Shaft: ‘AISI 304’ Stainless steel

Mechanical seal: Lower side (pump): Silicon Carbide. - Upper side (motor): Ceramic/Graphite.

Screws: Stainless steel

Joints: NBR

Foot support: Zinc-plated steel

SUPERSAND

Submersible electro-pump for sump and drainage

APPLICATIONS

Submersible electro-pumps specially designed for drainage and dewatering of muddy water in mines, open wells, drying of formwork or ditch and channel digging.

TECHNICAL CHARACTERISTICS

Type: Submersible

Flow (m3/h): 114-3,6

Head (m): 2-35

rpm: 2850

IP: 68

Isolation: B/F

Cooling: Pumped water

Max. Immersion depth: 30 m.

Temp. max. (ºC): 40

Max. density: 1100 Kg/m3

pH: 6 - 13

Thermal and amperimetric internal motor protection.

All models are supplied with 10 m. of electric cable.

Models SUPERSAND AG include a mixer for a more efficient pumping of muddy water.

MATERIALS

Pump body: ‘AISI 304’ Stainless steel

Motor casing: ‘AISI 304’ Stainless steel

Motor cover: Cast iron

Impeller: Cast iron and hardened chrome with high resistance to abrasion (60 Rockell hardness)

Shaft: ‘AISI 403’ Stainless steel

Double mechanical seal: Silicon Carbide + Carbon/Ceramic

Grid: Hardened cast iron

SRI

Submersible electro-pump for residual water

APPLICATIONS

Submersible pumps SRI series are suitable for industrial water treatment, pumping of water with acid, sea water, petrol station waste with acid from batteries, waste water from chemical processes and all type of liquids with suspended particles in general.

Specially necessary in the tanning industry and for chemical and pharmaceutical processes, laboratories and hospitals.

TECHNICAL CHARACTERISTICS

Type: Submersible Inox

Flow (m3/h): 2 - 69

Head (m): 2 - 24

rpm: 2850

IP: 68

Isolation: B

Cooling: Pumped water

Temp. max. (ºC): 40

Max. density: 1100 kg/m3

Max. viscosity: 100 cPs

pH: 3 - 13

All single-phase models are supplied with built-in level switch.

All models are supplied with 10 mt of santoprene cable with cable gland for higher protection against very aggressive liquids.

MATERIALS

Pump body: ‘AISI 316’ Stainless steel

Impeller: ‘AISI 316’ Stainless steel

Shaft: ‘AISI 316’ Stainless steel

Screws: ‘AISI 316’ Stainless steel

Double mechanical seal: Silicon Carbide/Siicon Carbide/Viton

O’rings: Viton

OXIGENADORES

Waste water aeration devices

APPLICATIONS

Devices for the agitation/aeration of waste water.

Suitable for all kinds of oxygenation of organic effluent, sludges, septic tanks, reduction of odours in pools and basins, reduction of foams and other industrial processes where it is necessary to add extra oxygen.

These devices are based on the Venturi effect, which involves the entry of surface air into the fluid to be treated, achieving an optimum mixture of agitation/aeration in the facility.

TECHNICAL CHARACTERISTICS

Type: Submersible

IP: 68

Isolation: F

Hz: 50

Cooling: Dielectric oil

Temp. max. (ºC): 40

Ø Solids: 20 mm

Max. density: 1100 Kg/m3

pH: 6 - 10

All models are supplied with 10 m. of electric cable and counterflange for assembly with gasket and screws.

Supplied with Venturi but without vertical pipe for air suction.

AGITADORES

Waste water agitation devices

APPLICATIONS

Submersible agitators suitable for the homogenisation of silts and liquids containing suspended foreign bodies.

Ideal for avoiding sedimentation in septic tanks, waste water transfer tanks, etc.

Maximum capacity of Oxygen addition 45Kg/h.

TECHNICAL CHARACTERISTICS

Type: Submersible

IP: 68

Isolation: F

Hz: 50

Cooling: Pumped water

Temp. max. (ºC): 40

Max. immersion depth: 20 m.

pH: 6 - 10

Motors are equipped with 2 thermal sensors (T1/T2) in the winding which display the temperature inside the motor, and an electrode (S) wich produces a signal revealing a fluid infiltration in the mechanical seal chamber. These sensors should be correctly connected to the suitable control panel, which is not included with the pump.

MATERIALS

Motor casing: GG25 cast iron

Propeller support: GG25 cast iron

Propeller: GG25 cast iron

Shaft: ‘AISI 420’ Stainless steel

GTSB

Self-suction electro-pumps on frame for residual water

APPLICATIONS

Self-priming electro-pumps without foot valve.

Suitable for waste water transfer, loaded liquids, lime milk, syrups, paper paste, etc

Very useful in chemical industries, canning industries, paper industries, mine industries, navy industries and refineries.

TECHNICAL CHARACTERISTICS

Type: Self-priming execution on base plate for waste water

Flow (m3/h): 8 - 120

Head (m): 5 - 40

rpm: 2900

IP: 54

Cooling: External ventilation

Temp. max. (ºC): 95

Max. suction depth: 6,5 m.

MATERIALS

Pump body: Cast iron

Motor support: Cast iron

Impeller: Cast iron

Shaft: Stainless steel

Mechanical seal: Ceramic/Graphite

HASAFOS

Pumping station

APPLICATIONS

Automatic pumping stations for the storing and over-lifting of waste and rain water without need for civil construction work.

With registerable watertight cover assuring tightness to gas and liquids.

Complete pitch of waste water pump/s (vortex impeller) II 230 v. with 5 mts. cable and level switch.

Fast coupling foot/s with guide rails for the pump/s extraction, so that handling inside the pumping station is not required.

TECHNICAL CHARACTERISTICS

Type: Pumping station

Flow (m3/h): 1 - 52

Height (m): 2 - 11

rpm: 2850

IP: 68

Isolation: F

MATERIALS

HASA-FOS tank: High density Polyethilene

MINIPAF pumps: G25 Cast iron

Coupling foot: G25 Cast iron

Internal installation (water discharge): PVC

Cooling: Oil and pumped water

Temp. max. (ºC): 40

HASAFOS100

Automatic pumping station for domestic applications

APPLICATIONS

Automatic pumping station for domestic applications like sewage, rain water and fecal water pumping without the need for civil works.

With a waterproof cover that guarantees a gas and liquid tightness.

It is supplied with a submersible pump mounted inside, which incorporates a full-pass vortex turbine and level switch for automatic operation.

CHARACTERISTICS

Range: HASA-FOS 100

Type: Pumping station

Flow (m3/h): 1,2 - 22

Head (m): 0 - 11

rpm: 2850

IP: 68

Isolation: F

Cooling: Oil and pumped water

Temp. max. (ºC): 40

COMPOSITON

Volume of tank: 100 L.

N. Pumps: 1 INOX-PALM 2A de 1'2CV II 230 V

Outlets for cables: 1 x SHUKO Plug

Dimensions (Width x depth x heigth): 500 x 760 x 590 mm

Ventilation outlet: DIN-40

Waste water outlet: 1 1/4"

Entrada recogida aguas residuales: DN-125

Access cover: Diameter 400 mm.

MATERIALS

HASA-FOS 100 l. tank: High density Polyethilene.

INOX-PALM 2A pump: Cast iron G20 + 'AISI 304' Stainless steel.

Internal installation (water discharge): PVC.

ESTACIONBOMBEO

Pumping stations for waste water

APPLICATIONS

Pumping stations for collection and evacuation of sewage and waste water of all kind from places under the sewage level.

The pumping stations are available with several types of submersible pumps (open impeller, single-channel, vortex or with grinding system) depending on the kind of water to be lifted (rain, seweage, fecal, etc.).

They can be provided fully-equipped like prefabricated wells with a collection tank, electropumps, internal pipes and valves system, coupling foot, level switches and protection and control pânel; or for being assembled on concrete manholes with all the necessary components. pipes and valves system, coupling foot, level switches and protection and control switchboard; or for being assembled on concrete manholes with all the necessary components.

COMPONENTS

SUBMERSIBLE PUMP: we have several pump models with different types of impellers (open, single-channel, vortex, grinder), the choice of the kind of impeller depends on its application. They have an output diameter from 1 1/4” (DN-32) to DN-150. The passage of foreign bodies is an important factor to be considered.

COLLECTION TANK: they are manufactured under request according to the size or volume specified by the customer.

COUPLING FOOT: they are used for the assembly in the fixed installation allowing an easy removal of the pumps without the need to remove the discharge tube, thanks to a system of two guide rails that allows the automatic coupling of the pumps. The sealing of the installation is guaranteed by the pump’s weight. without the need to remove the discharge tube, thanks to a system of two guide tubes that allows the automatic coupling of the pumps. The sealing of the installation is guaranteed by the pump’s weight.

CONTROL AND PROTECTION SWITCHBOARD: it controls the maoeuvre of the pump/s through level switches and has electrical protection by circuit breaker or relay. It performs the alternation during the start and has acoustic alarm for overflow.

LEVEL SWITCHES: they are necessary for the start and stop manoeuvre of the pumps: one is for the stop of the pump/s (if there are several pumps the stop is at once), another one is for the start of every pump and another one for the overfl ow alarm.

VALVES: we have shut-off ball valves and check ball valves in PVC from DN-32 (1 1/4”) to DN-80 (3”).

TRAMPILLA

Accessories for installations of residual water - Trap door

SEPTIC TANK TRAP

Galvanized trap with siphonic closing for septic tanks, sizes:

900x450

900x550

800x600

900x700

1000x800

1200x900

PIEACOPLAMIENTO

Accessories for installations of residual water - Coupling stand

COUPLING FOOT

Coupling foot in cast iron for waste water

Suitable for IPX, PAF, MINIPAF, INOX-PALM, TRITURANT and AT/VT

VRETENCIONBOLA

Accessories for installations of residual water - Retention ball valve

RETENTION/SHUT-OFF BALL VALVES IN PVC

Retention ball valves in PVC that enables complete pitch of pumped liquid

1¼'' - 1½'' - 2'' - 2½'' - 3'' thread

CLARIF-ESTANDAR

Grey water clarifier

APPLICATIONS

Simple and domestic depuration equipment based on a physical-chemical process for the recycling of grey water from showers and baths, aimed at achieving further reutilization of such water for the filling of cisterns and lavatories.

COMPONENTS

250 l. grey water accumulation tank with inlet for grey water, safety trough, emptying valve and access inlet for maintenance.

Pressure equipment JETBOX 100/PRESSCONTROL 1CV II 230V

Electro-valve for occasional filling with water from the supply network with open vessel in order to prevent pollution on drinking water.

Level switches for the control of the pressure unit and filling electro-valve

Cartridge prefilter of 100 microns for foreign bodies.

General control panel.

Manometer for working pressure checking.

Accumulation tank 10 L and dispenser pump for sodium hypochlorite

Accumulation tank 10 L and dispenser pump for diluted food colouring (optional)

Ultraviolet cell (optional)

CLARIF-COMPACT

Grey water clarifier

APPLICATIONS

Simple and domestic depuration equipment based on a physical-chemical process for the recycling of grey water from showers and baths, aimed at achieving further reutilization of such water for the filling of cisterns and lavatories.

COMPONENTS

Grey water accumulation tank (150, 300 or 500 L) in reinforced with fiberglass polyester with inlet for grey water, safety overfl ow, emptying valve and access inlet for maintenance

Submersible pump ATENAS 103 M II 230V

Pressure regulator LOGICPRESS

Level switch HASA-85 2m. cable.

Filter in Nylon for solids

Bottom valve in stainless steel to secure a minimum level water in the purifying machine in case of not having grey water.

Peristaltic pump and programmer for batching of sodium hypochlorite (bleach)

Peristaltic pump and programmer for the dosing of diluted colorant (optional)

Dispenser for the treatment of chemical products

BIOGRIS-HOGAR

Grey water clarifier

APPLICATIONS

Compact greywater recovery system.

For convenient installation in homes

Water can be collected from the drains of sinks, showers and bathtubs, for reuse in non-potable purposes such as filling toilet cisterns, watering gardens or cleaning pavements.

This practice has great advantages from an environmental point of view, while at the same time offers savings in water consumption.

CHARACTERISTICS

Pre treatments: Three lapping separation sections and sedimentation with automatic valve and air pumps with scheduled discharges.

Treatment with bag filter: Tank with interchangeable bag filter for hair parting residues and for the material sedimented.

Biological treatment: Equalization and oxidation tank equipped with ultrafiltration membrane and suction pump of purified water.

Disinfection: High pressure UV sterilization lamp 0.20 kW/h.

Pressure system: Multi-stage centrifugal pump (0,55 kW/0,75 HP) with pressure controler.

Control unit: Control unit equipped with APP for smartphones with visualization of operation data, consumption, water and energy saving and maintenance alarms.

Maintenance: Replacing the hair bag filter (approx 1 time per month), cleaning of the ultrafiltration membrane (rinsing with running water approximately once a year).